| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
dm-raid456, md/raid456: fix a deadlock for dm-raid456 while io concurrent with reshape
For raid456, if reshape is still in progress, then IO across reshape
position will wait for reshape to make progress. However, for dm-raid,
in following cases reshape will never make progress hence IO will hang:
1) the array is read-only;
2) MD_RECOVERY_WAIT is set;
3) MD_RECOVERY_FROZEN is set;
After commit c467e97f079f ("md/raid6: use valid sector values to determine
if an I/O should wait on the reshape") fix the problem that IO across
reshape position doesn't wait for reshape, the dm-raid test
shell/lvconvert-raid-reshape.sh start to hang:
[root@fedora ~]# cat /proc/979/stack
[<0>] wait_woken+0x7d/0x90
[<0>] raid5_make_request+0x929/0x1d70 [raid456]
[<0>] md_handle_request+0xc2/0x3b0 [md_mod]
[<0>] raid_map+0x2c/0x50 [dm_raid]
[<0>] __map_bio+0x251/0x380 [dm_mod]
[<0>] dm_submit_bio+0x1f0/0x760 [dm_mod]
[<0>] __submit_bio+0xc2/0x1c0
[<0>] submit_bio_noacct_nocheck+0x17f/0x450
[<0>] submit_bio_noacct+0x2bc/0x780
[<0>] submit_bio+0x70/0xc0
[<0>] mpage_readahead+0x169/0x1f0
[<0>] blkdev_readahead+0x18/0x30
[<0>] read_pages+0x7c/0x3b0
[<0>] page_cache_ra_unbounded+0x1ab/0x280
[<0>] force_page_cache_ra+0x9e/0x130
[<0>] page_cache_sync_ra+0x3b/0x110
[<0>] filemap_get_pages+0x143/0xa30
[<0>] filemap_read+0xdc/0x4b0
[<0>] blkdev_read_iter+0x75/0x200
[<0>] vfs_read+0x272/0x460
[<0>] ksys_read+0x7a/0x170
[<0>] __x64_sys_read+0x1c/0x30
[<0>] do_syscall_64+0xc6/0x230
[<0>] entry_SYSCALL_64_after_hwframe+0x6c/0x74
This is because reshape can't make progress.
For md/raid, the problem doesn't exist because register new sync_thread
doesn't rely on the IO to be done any more:
1) If array is read-only, it can switch to read-write by ioctl/sysfs;
2) md/raid never set MD_RECOVERY_WAIT;
3) If MD_RECOVERY_FROZEN is set, mddev_suspend() doesn't hold
'reconfig_mutex', hence it can be cleared and reshape can continue by
sysfs api 'sync_action'.
However, I'm not sure yet how to avoid the problem in dm-raid yet. This
patch on the one hand make sure raid_message() can't change
sync_thread() through raid_message() after presuspend(), on the other
hand detect the above 3 cases before wait for IO do be done in
dm_suspend(), and let dm-raid requeue those IO. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Fix command flush on cable pull
System crash due to command failed to flush back to SCSI layer.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
PGD 0 P4D 0
Oops: 0000 [#1] SMP NOPTI
CPU: 27 PID: 793455 Comm: kworker/u130:6 Kdump: loaded Tainted: G OE --------- - - 4.18.0-372.9.1.el8.x86_64 #1
Hardware name: HPE ProLiant DL360 Gen10/ProLiant DL360 Gen10, BIOS U32 09/03/2021
Workqueue: nvme-wq nvme_fc_connect_ctrl_work [nvme_fc]
RIP: 0010:__wake_up_common+0x4c/0x190
Code: 24 10 4d 85 c9 74 0a 41 f6 01 04 0f 85 9d 00 00 00 48 8b 43 08 48 83 c3 08 4c 8d 48 e8 49 8d 41 18 48 39 c3 0f 84 f0 00 00 00 <49> 8b 41 18 89 54 24 08 31 ed 4c 8d 70 e8 45 8b 29 41 f6 c5 04 75
RSP: 0018:ffff95f3e0cb7cd0 EFLAGS: 00010086
RAX: 0000000000000000 RBX: ffff8b08d3b26328 RCX: 0000000000000000
RDX: 0000000000000001 RSI: 0000000000000003 RDI: ffff8b08d3b26320
RBP: 0000000000000001 R08: 0000000000000000 R09: ffffffffffffffe8
R10: 0000000000000000 R11: ffff95f3e0cb7a60 R12: ffff95f3e0cb7d20
R13: 0000000000000003 R14: 0000000000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff8b2fdf6c0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000002f1e410002 CR4: 00000000007706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
__wake_up_common_lock+0x7c/0xc0
qla_nvme_ls_req+0x355/0x4c0 [qla2xxx]
qla2xxx [0000:12:00.1]-f084:3: qlt_free_session_done: se_sess 0000000000000000 / sess ffff8ae1407ca000 from port 21:32:00:02:ac:07:ee:b8 loop_id 0x02 s_id 01:02:00 logout 1 keep 0 els_logo 0
? __nvme_fc_send_ls_req+0x260/0x380 [nvme_fc]
qla2xxx [0000:12:00.1]-207d:3: FCPort 21:32:00:02:ac:07:ee:b8 state transitioned from ONLINE to LOST - portid=010200.
? nvme_fc_send_ls_req.constprop.42+0x1a/0x45 [nvme_fc]
qla2xxx [0000:12:00.1]-2109:3: qla2x00_schedule_rport_del 21320002ac07eeb8. rport ffff8ae598122000 roles 1
? nvme_fc_connect_ctrl_work.cold.63+0x1e3/0xa7d [nvme_fc]
qla2xxx [0000:12:00.1]-f084:3: qlt_free_session_done: se_sess 0000000000000000 / sess ffff8ae14801e000 from port 21:32:01:02:ad:f7:ee:b8 loop_id 0x04 s_id 01:02:01 logout 1 keep 0 els_logo 0
? __switch_to+0x10c/0x450
? process_one_work+0x1a7/0x360
qla2xxx [0000:12:00.1]-207d:3: FCPort 21:32:01:02:ad:f7:ee:b8 state transitioned from ONLINE to LOST - portid=010201.
? worker_thread+0x1ce/0x390
? create_worker+0x1a0/0x1a0
qla2xxx [0000:12:00.1]-2109:3: qla2x00_schedule_rport_del 21320102adf7eeb8. rport ffff8ae3b2312800 roles 70
? kthread+0x10a/0x120
qla2xxx [0000:12:00.1]-2112:3: qla_nvme_unregister_remote_port: unregister remoteport on ffff8ae14801e000 21320102adf7eeb8
? set_kthread_struct+0x40/0x40
qla2xxx [0000:12:00.1]-2110:3: remoteport_delete of ffff8ae14801e000 21320102adf7eeb8 completed.
? ret_from_fork+0x1f/0x40
qla2xxx [0000:12:00.1]-f086:3: qlt_free_session_done: waiting for sess ffff8ae14801e000 logout
The system was under memory stress where driver was not able to allocate an
SRB to carry out error recovery of cable pull. The failure to flush causes
upper layer to start modifying scsi_cmnd. When the system frees up some
memory, the subsequent cable pull trigger another command flush. At this
point the driver access a null pointer when attempting to DMA unmap the
SGL.
Add a check to make sure commands are flush back on session tear down to
prevent the null pointer access. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Fix double free of the ha->vp_map pointer
Coverity scan reported potential risk of double free of the pointer
ha->vp_map. ha->vp_map was freed in qla2x00_mem_alloc(), and again freed
in function qla2x00_mem_free(ha).
Assign NULL to vp_map and kfree take care of NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix potential UAF in cifs_debug_files_proc_show()
Skip sessions that are being teared down (status == SES_EXITING) to
avoid UAF. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mlx5: Fix fortify source warning while accessing Eth segment
------------[ cut here ]------------
memcpy: detected field-spanning write (size 56) of single field "eseg->inline_hdr.start" at /var/lib/dkms/mlnx-ofed-kernel/5.8/build/drivers/infiniband/hw/mlx5/wr.c:131 (size 2)
WARNING: CPU: 0 PID: 293779 at /var/lib/dkms/mlnx-ofed-kernel/5.8/build/drivers/infiniband/hw/mlx5/wr.c:131 mlx5_ib_post_send+0x191b/0x1a60 [mlx5_ib]
Modules linked in: 8021q garp mrp stp llc rdma_ucm(OE) rdma_cm(OE) iw_cm(OE) ib_ipoib(OE) ib_cm(OE) ib_umad(OE) mlx5_ib(OE) ib_uverbs(OE) ib_core(OE) mlx5_core(OE) pci_hyperv_intf mlxdevm(OE) mlx_compat(OE) tls mlxfw(OE) psample nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip_set nf_tables libcrc32c nfnetlink mst_pciconf(OE) knem(OE) vfio_pci vfio_pci_core vfio_iommu_type1 vfio iommufd irqbypass cuse nfsv3 nfs fscache netfs xfrm_user xfrm_algo ipmi_devintf ipmi_msghandler binfmt_misc crct10dif_pclmul crc32_pclmul polyval_clmulni polyval_generic ghash_clmulni_intel sha512_ssse3 snd_pcsp aesni_intel crypto_simd cryptd snd_pcm snd_timer joydev snd soundcore input_leds serio_raw evbug nfsd auth_rpcgss nfs_acl lockd grace sch_fq_codel sunrpc drm efi_pstore ip_tables x_tables autofs4 psmouse virtio_net net_failover failover floppy
[last unloaded: mlx_compat(OE)]
CPU: 0 PID: 293779 Comm: ssh Tainted: G OE 6.2.0-32-generic #32~22.04.1-Ubuntu
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
RIP: 0010:mlx5_ib_post_send+0x191b/0x1a60 [mlx5_ib]
Code: 0c 01 00 a8 01 75 25 48 8b 75 a0 b9 02 00 00 00 48 c7 c2 10 5b fd c0 48 c7 c7 80 5b fd c0 c6 05 57 0c 03 00 01 e8 95 4d 93 da <0f> 0b 44 8b 4d b0 4c 8b 45 c8 48 8b 4d c0 e9 49 fb ff ff 41 0f b7
RSP: 0018:ffffb5b48478b570 EFLAGS: 00010046
RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffffb5b48478b628 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffffb5b48478b5e8
R13: ffff963a3c609b5e R14: ffff9639c3fbd800 R15: ffffb5b480475a80
FS: 00007fc03b444c80(0000) GS:ffff963a3dc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000556f46bdf000 CR3: 0000000006ac6003 CR4: 00000000003706f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
? show_regs+0x72/0x90
? mlx5_ib_post_send+0x191b/0x1a60 [mlx5_ib]
? __warn+0x8d/0x160
? mlx5_ib_post_send+0x191b/0x1a60 [mlx5_ib]
? report_bug+0x1bb/0x1d0
? handle_bug+0x46/0x90
? exc_invalid_op+0x19/0x80
? asm_exc_invalid_op+0x1b/0x20
? mlx5_ib_post_send+0x191b/0x1a60 [mlx5_ib]
mlx5_ib_post_send_nodrain+0xb/0x20 [mlx5_ib]
ipoib_send+0x2ec/0x770 [ib_ipoib]
ipoib_start_xmit+0x5a0/0x770 [ib_ipoib]
dev_hard_start_xmit+0x8e/0x1e0
? validate_xmit_skb_list+0x4d/0x80
sch_direct_xmit+0x116/0x3a0
__dev_xmit_skb+0x1fd/0x580
__dev_queue_xmit+0x284/0x6b0
? _raw_spin_unlock_irq+0xe/0x50
? __flush_work.isra.0+0x20d/0x370
? push_pseudo_header+0x17/0x40 [ib_ipoib]
neigh_connected_output+0xcd/0x110
ip_finish_output2+0x179/0x480
? __smp_call_single_queue+0x61/0xa0
__ip_finish_output+0xc3/0x190
ip_finish_output+0x2e/0xf0
ip_output+0x78/0x110
? __pfx_ip_finish_output+0x10/0x10
ip_local_out+0x64/0x70
__ip_queue_xmit+0x18a/0x460
ip_queue_xmit+0x15/0x30
__tcp_transmit_skb+0x914/0x9c0
tcp_write_xmit+0x334/0x8d0
tcp_push_one+0x3c/0x60
tcp_sendmsg_locked+0x2e1/0xac0
tcp_sendmsg+0x2d/0x50
inet_sendmsg+0x43/0x90
sock_sendmsg+0x68/0x80
sock_write_iter+0x93/0x100
vfs_write+0x326/0x3c0
ksys_write+0xbd/0xf0
? do_syscall_64+0x69/0x90
__x64_sys_write+0x19/0x30
do_syscall_
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
x86/mm: Disallow vsyscall page read for copy_from_kernel_nofault()
When trying to use copy_from_kernel_nofault() to read vsyscall page
through a bpf program, the following oops was reported:
BUG: unable to handle page fault for address: ffffffffff600000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 3231067 P4D 3231067 PUD 3233067 PMD 3235067 PTE 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 1 PID: 20390 Comm: test_progs ...... 6.7.0+ #58
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) ......
RIP: 0010:copy_from_kernel_nofault+0x6f/0x110
......
Call Trace:
<TASK>
? copy_from_kernel_nofault+0x6f/0x110
bpf_probe_read_kernel+0x1d/0x50
bpf_prog_2061065e56845f08_do_probe_read+0x51/0x8d
trace_call_bpf+0xc5/0x1c0
perf_call_bpf_enter.isra.0+0x69/0xb0
perf_syscall_enter+0x13e/0x200
syscall_trace_enter+0x188/0x1c0
do_syscall_64+0xb5/0xe0
entry_SYSCALL_64_after_hwframe+0x6e/0x76
</TASK>
......
---[ end trace 0000000000000000 ]---
The oops is triggered when:
1) A bpf program uses bpf_probe_read_kernel() to read from the vsyscall
page and invokes copy_from_kernel_nofault() which in turn calls
__get_user_asm().
2) Because the vsyscall page address is not readable from kernel space,
a page fault exception is triggered accordingly.
3) handle_page_fault() considers the vsyscall page address as a user
space address instead of a kernel space address. This results in the
fix-up setup by bpf not being applied and a page_fault_oops() is invoked
due to SMAP.
Considering handle_page_fault() has already considered the vsyscall page
address as a userspace address, fix the problem by disallowing vsyscall
page read for copy_from_kernel_nofault(). |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: rfcomm: Fix null-ptr-deref in rfcomm_check_security
During our fuzz testing of the connection and disconnection process at the
RFCOMM layer, we discovered this bug. By comparing the packets from a
normal connection and disconnection process with the testcase that
triggered a KASAN report. We analyzed the cause of this bug as follows:
1. In the packets captured during a normal connection, the host sends a
`Read Encryption Key Size` type of `HCI_CMD` packet
(Command Opcode: 0x1408) to the controller to inquire the length of
encryption key.After receiving this packet, the controller immediately
replies with a Command Completepacket (Event Code: 0x0e) to return the
Encryption Key Size.
2. In our fuzz test case, the timing of the controller's response to this
packet was delayed to an unexpected point: after the RFCOMM and L2CAP
layers had disconnected but before the HCI layer had disconnected.
3. After receiving the Encryption Key Size Response at the time described
in point 2, the host still called the rfcomm_check_security function.
However, by this time `struct l2cap_conn *conn = l2cap_pi(sk)->chan->conn;`
had already been released, and when the function executed
`return hci_conn_security(conn->hcon, d->sec_level, auth_type, d->out);`,
specifically when accessing `conn->hcon`, a null-ptr-deref error occurred.
To fix this bug, check if `sk->sk_state` is BT_CLOSED before calling
rfcomm_recv_frame in rfcomm_process_rx. |
| In the Linux kernel, the following vulnerability has been resolved:
quota: Fix potential NULL pointer dereference
Below race may cause NULL pointer dereference
P1 P2
dquot_free_inode quota_off
drop_dquot_ref
remove_dquot_ref
dquots = i_dquot(inode)
dquots = i_dquot(inode)
srcu_read_lock
dquots[cnt]) != NULL (1)
dquots[type] = NULL (2)
spin_lock(&dquots[cnt]->dq_dqb_lock) (3)
....
If dquot_free_inode(or other routines) checks inode's quota pointers (1)
before quota_off sets it to NULL(2) and use it (3) after that, NULL pointer
dereference will be triggered.
So let's fix it by using a temporary pointer to avoid this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-fc: do not wait in vain when unloading module
The module exit path has race between deleting all controllers and
freeing 'left over IDs'. To prevent double free a synchronization
between nvme_delete_ctrl and ida_destroy has been added by the initial
commit.
There is some logic around trying to prevent from hanging forever in
wait_for_completion, though it does not handling all cases. E.g.
blktests is able to reproduce the situation where the module unload
hangs forever.
If we completely rely on the cleanup code executed from the
nvme_delete_ctrl path, all IDs will be freed eventually. This makes
calling ida_destroy unnecessary. We only have to ensure that all
nvme_delete_ctrl code has been executed before we leave
nvme_fc_exit_module. This is done by flushing the nvme_delete_wq
workqueue.
While at it, remove the unused nvme_fc_wq workqueue too. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix race condition on enabling fast-xmit
fast-xmit must only be enabled after the sta has been uploaded to the driver,
otherwise it could end up passing the not-yet-uploaded sta via drv_tx calls
to the driver, leading to potential crashes because of uninitialized drv_priv
data.
Add a missing sta->uploaded check and re-check fast xmit after inserting a sta. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: avoid allocating blocks from corrupted group in ext4_mb_try_best_found()
Determine if the group block bitmap is corrupted before using ac_b_ex in
ext4_mb_try_best_found() to avoid allocating blocks from a group with a
corrupted block bitmap in the following concurrency and making the
situation worse.
ext4_mb_regular_allocator
ext4_lock_group(sb, group)
ext4_mb_good_group
// check if the group bbitmap is corrupted
ext4_mb_complex_scan_group
// Scan group gets ac_b_ex but doesn't use it
ext4_unlock_group(sb, group)
ext4_mark_group_bitmap_corrupted(group)
// The block bitmap was corrupted during
// the group unlock gap.
ext4_mb_try_best_found
ext4_lock_group(ac->ac_sb, group)
ext4_mb_use_best_found
mb_mark_used
// Allocating blocks in block bitmap corrupted group |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: avoid allocating blocks from corrupted group in ext4_mb_find_by_goal()
Places the logic for checking if the group's block bitmap is corrupt under
the protection of the group lock to avoid allocating blocks from the group
with a corrupted block bitmap. |
| In the Linux kernel, the following vulnerability has been resolved:
nouveau: offload fence uevents work to workqueue
This should break the deadlock between the fctx lock and the irq lock.
This offloads the processing off the work from the irq into a workqueue. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/proc: do_task_stat: use sig->stats_lock to gather the threads/children stats
lock_task_sighand() can trigger a hard lockup. If NR_CPUS threads call
do_task_stat() at the same time and the process has NR_THREADS, it will
spin with irqs disabled O(NR_CPUS * NR_THREADS) time.
Change do_task_stat() to use sig->stats_lock to gather the statistics
outside of ->siglock protected section, in the likely case this code will
run lockless. |
| In the Linux kernel, the following vulnerability has been resolved:
blk-mq: fix IO hang from sbitmap wakeup race
In blk_mq_mark_tag_wait(), __add_wait_queue() may be re-ordered
with the following blk_mq_get_driver_tag() in case of getting driver
tag failure.
Then in __sbitmap_queue_wake_up(), waitqueue_active() may not observe
the added waiter in blk_mq_mark_tag_wait() and wake up nothing, meantime
blk_mq_mark_tag_wait() can't get driver tag successfully.
This issue can be reproduced by running the following test in loop, and
fio hang can be observed in < 30min when running it on my test VM
in laptop.
modprobe -r scsi_debug
modprobe scsi_debug delay=0 dev_size_mb=4096 max_queue=1 host_max_queue=1 submit_queues=4
dev=`ls -d /sys/bus/pseudo/drivers/scsi_debug/adapter*/host*/target*/*/block/* | head -1 | xargs basename`
fio --filename=/dev/"$dev" --direct=1 --rw=randrw --bs=4k --iodepth=1 \
--runtime=100 --numjobs=40 --time_based --name=test \
--ioengine=libaio
Fix the issue by adding one explicit barrier in blk_mq_mark_tag_wait(), which
is just fine in case of running out of tag. |
| In the Linux kernel, the following vulnerability has been resolved:
xhci: handle isoc Babble and Buffer Overrun events properly
xHCI 4.9 explicitly forbids assuming that the xHC has released its
ownership of a multi-TRB TD when it reports an error on one of the
early TRBs. Yet the driver makes such assumption and releases the TD,
allowing the remaining TRBs to be freed or overwritten by new TDs.
The xHC should also report completion of the final TRB due to its IOC
flag being set by us, regardless of prior errors. This event cannot
be recognized if the TD has already been freed earlier, resulting in
"Transfer event TRB DMA ptr not part of current TD" error message.
Fix this by reusing the logic for processing isoc Transaction Errors.
This also handles hosts which fail to report the final completion.
Fix transfer length reporting on Babble errors. They may be caused by
device malfunction, no guarantee that the buffer has been filled. |
| In the Linux kernel, the following vulnerability has been resolved:
fs: prevent out-of-bounds array speculation when closing a file descriptor
Google-Bug-Id: 114199369 |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/iommu: fix memory leak with using debugfs_lookup()
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: iscsi_tcp: Fix UAF during logout when accessing the shost ipaddress
Bug report and analysis from Ding Hui.
During iSCSI session logout, if another task accesses the shost ipaddress
attr, we can get a KASAN UAF report like this:
[ 276.942144] BUG: KASAN: use-after-free in _raw_spin_lock_bh+0x78/0xe0
[ 276.942535] Write of size 4 at addr ffff8881053b45b8 by task cat/4088
[ 276.943511] CPU: 2 PID: 4088 Comm: cat Tainted: G E 6.1.0-rc8+ #3
[ 276.943997] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 11/12/2020
[ 276.944470] Call Trace:
[ 276.944943] <TASK>
[ 276.945397] dump_stack_lvl+0x34/0x48
[ 276.945887] print_address_description.constprop.0+0x86/0x1e7
[ 276.946421] print_report+0x36/0x4f
[ 276.947358] kasan_report+0xad/0x130
[ 276.948234] kasan_check_range+0x35/0x1c0
[ 276.948674] _raw_spin_lock_bh+0x78/0xe0
[ 276.949989] iscsi_sw_tcp_host_get_param+0xad/0x2e0 [iscsi_tcp]
[ 276.951765] show_host_param_ISCSI_HOST_PARAM_IPADDRESS+0xe9/0x130 [scsi_transport_iscsi]
[ 276.952185] dev_attr_show+0x3f/0x80
[ 276.953005] sysfs_kf_seq_show+0x1fb/0x3e0
[ 276.953401] seq_read_iter+0x402/0x1020
[ 276.954260] vfs_read+0x532/0x7b0
[ 276.955113] ksys_read+0xed/0x1c0
[ 276.955952] do_syscall_64+0x38/0x90
[ 276.956347] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[ 276.956769] RIP: 0033:0x7f5d3a679222
[ 276.957161] Code: c0 e9 b2 fe ff ff 50 48 8d 3d 32 c0 0b 00 e8 a5 fe 01 00 0f 1f 44 00 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 0f 05 <48> 3d 00 f0 ff ff 77 56 c3 0f 1f 44 00 00 48 83 ec 28 48 89 54 24
[ 276.958009] RSP: 002b:00007ffc864d16a8 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
[ 276.958431] RAX: ffffffffffffffda RBX: 0000000000020000 RCX: 00007f5d3a679222
[ 276.958857] RDX: 0000000000020000 RSI: 00007f5d3a4fe000 RDI: 0000000000000003
[ 276.959281] RBP: 00007f5d3a4fe000 R08: 00000000ffffffff R09: 0000000000000000
[ 276.959682] R10: 0000000000000022 R11: 0000000000000246 R12: 0000000000020000
[ 276.960126] R13: 0000000000000003 R14: 0000000000000000 R15: 0000557a26dada58
[ 276.960536] </TASK>
[ 276.961357] Allocated by task 2209:
[ 276.961756] kasan_save_stack+0x1e/0x40
[ 276.962170] kasan_set_track+0x21/0x30
[ 276.962557] __kasan_kmalloc+0x7e/0x90
[ 276.962923] __kmalloc+0x5b/0x140
[ 276.963308] iscsi_alloc_session+0x28/0x840 [scsi_transport_iscsi]
[ 276.963712] iscsi_session_setup+0xda/0xba0 [libiscsi]
[ 276.964078] iscsi_sw_tcp_session_create+0x1fd/0x330 [iscsi_tcp]
[ 276.964431] iscsi_if_create_session.isra.0+0x50/0x260 [scsi_transport_iscsi]
[ 276.964793] iscsi_if_recv_msg+0xc5a/0x2660 [scsi_transport_iscsi]
[ 276.965153] iscsi_if_rx+0x198/0x4b0 [scsi_transport_iscsi]
[ 276.965546] netlink_unicast+0x4d5/0x7b0
[ 276.965905] netlink_sendmsg+0x78d/0xc30
[ 276.966236] sock_sendmsg+0xe5/0x120
[ 276.966576] ____sys_sendmsg+0x5fe/0x860
[ 276.966923] ___sys_sendmsg+0xe0/0x170
[ 276.967300] __sys_sendmsg+0xc8/0x170
[ 276.967666] do_syscall_64+0x38/0x90
[ 276.968028] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[ 276.968773] Freed by task 2209:
[ 276.969111] kasan_save_stack+0x1e/0x40
[ 276.969449] kasan_set_track+0x21/0x30
[ 276.969789] kasan_save_free_info+0x2a/0x50
[ 276.970146] __kasan_slab_free+0x106/0x190
[ 276.970470] __kmem_cache_free+0x133/0x270
[ 276.970816] device_release+0x98/0x210
[ 276.971145] kobject_cleanup+0x101/0x360
[ 276.971462] iscsi_session_teardown+0x3fb/0x530 [libiscsi]
[ 276.971775] iscsi_sw_tcp_session_destroy+0xd8/0x130 [iscsi_tcp]
[ 276.972143] iscsi_if_recv_msg+0x1bf1/0x2660 [scsi_transport_iscsi]
[ 276.972485] iscsi_if_rx+0x198/0x4b0 [scsi_transport_iscsi]
[ 276.972808] netlink_unicast+0x4d5/0x7b0
[ 276.973201] netlink_sendmsg+0x78d/0xc30
[ 276.973544] sock_sendmsg+0xe5/0x120
[ 276.973864] ____sys_sendmsg+0x5fe/0x860
[ 276.974248] ___sys_
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: iscsi_tcp: Fix UAF during login when accessing the shost ipaddress
If during iscsi_sw_tcp_session_create() iscsi_tcp_r2tpool_alloc() fails,
userspace could be accessing the host's ipaddress attr. If we then free the
session via iscsi_session_teardown() while userspace is still accessing the
session we will hit a use after free bug.
Set the tcp_sw_host->session after we have completed session creation and
can no longer fail. |
