| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: bridge: xmit: make sure we have at least eth header len bytes
syzbot triggered an uninit value[1] error in bridge device's xmit path
by sending a short (less than ETH_HLEN bytes) skb. To fix it check if
we can actually pull that amount instead of assuming.
Tested with dropwatch:
drop at: br_dev_xmit+0xb93/0x12d0 [bridge] (0xffffffffc06739b3)
origin: software
timestamp: Mon May 13 11:31:53 2024 778214037 nsec
protocol: 0x88a8
length: 2
original length: 2
drop reason: PKT_TOO_SMALL
[1]
BUG: KMSAN: uninit-value in br_dev_xmit+0x61d/0x1cb0 net/bridge/br_device.c:65
br_dev_xmit+0x61d/0x1cb0 net/bridge/br_device.c:65
__netdev_start_xmit include/linux/netdevice.h:4903 [inline]
netdev_start_xmit include/linux/netdevice.h:4917 [inline]
xmit_one net/core/dev.c:3531 [inline]
dev_hard_start_xmit+0x247/0xa20 net/core/dev.c:3547
__dev_queue_xmit+0x34db/0x5350 net/core/dev.c:4341
dev_queue_xmit include/linux/netdevice.h:3091 [inline]
__bpf_tx_skb net/core/filter.c:2136 [inline]
__bpf_redirect_common net/core/filter.c:2180 [inline]
__bpf_redirect+0x14a6/0x1620 net/core/filter.c:2187
____bpf_clone_redirect net/core/filter.c:2460 [inline]
bpf_clone_redirect+0x328/0x470 net/core/filter.c:2432
___bpf_prog_run+0x13fe/0xe0f0 kernel/bpf/core.c:1997
__bpf_prog_run512+0xb5/0xe0 kernel/bpf/core.c:2238
bpf_dispatcher_nop_func include/linux/bpf.h:1234 [inline]
__bpf_prog_run include/linux/filter.h:657 [inline]
bpf_prog_run include/linux/filter.h:664 [inline]
bpf_test_run+0x499/0xc30 net/bpf/test_run.c:425
bpf_prog_test_run_skb+0x14ea/0x1f20 net/bpf/test_run.c:1058
bpf_prog_test_run+0x6b7/0xad0 kernel/bpf/syscall.c:4269
__sys_bpf+0x6aa/0xd90 kernel/bpf/syscall.c:5678
__do_sys_bpf kernel/bpf/syscall.c:5767 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5765 [inline]
__x64_sys_bpf+0xa0/0xe0 kernel/bpf/syscall.c:5765
x64_sys_call+0x96b/0x3b50 arch/x86/include/generated/asm/syscalls_64.h:322
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f |
| In the Linux kernel, the following vulnerability has been resolved:
fpga: manager: add owner module and take its refcount
The current implementation of the fpga manager assumes that the low-level
module registers a driver for the parent device and uses its owner pointer
to take the module's refcount. This approach is problematic since it can
lead to a null pointer dereference while attempting to get the manager if
the parent device does not have a driver.
To address this problem, add a module owner pointer to the fpga_manager
struct and use it to take the module's refcount. Modify the functions for
registering the manager to take an additional owner module parameter and
rename them to avoid conflicts. Use the old function names for helper
macros that automatically set the module that registers the manager as the
owner. This ensures compatibility with existing low-level control modules
and reduces the chances of registering a manager without setting the owner.
Also, update the documentation to keep it consistent with the new interface
for registering an fpga manager.
Other changes: opportunistically move put_device() from __fpga_mgr_get() to
fpga_mgr_get() and of_fpga_mgr_get() to improve code clarity since the
manager device is taken in these functions. |
| In the Linux kernel, the following vulnerability has been resolved:
gpiolib: cdev: Fix use after free in lineinfo_changed_notify
The use-after-free issue occurs as follows: when the GPIO chip device file
is being closed by invoking gpio_chrdev_release(), watched_lines is freed
by bitmap_free(), but the unregistration of lineinfo_changed_nb notifier
chain failed due to waiting write rwsem. Additionally, one of the GPIO
chip's lines is also in the release process and holds the notifier chain's
read rwsem. Consequently, a race condition leads to the use-after-free of
watched_lines.
Here is the typical stack when issue happened:
[free]
gpio_chrdev_release()
--> bitmap_free(cdev->watched_lines) <-- freed
--> blocking_notifier_chain_unregister()
--> down_write(&nh->rwsem) <-- waiting rwsem
--> __down_write_common()
--> rwsem_down_write_slowpath()
--> schedule_preempt_disabled()
--> schedule()
[use]
st54spi_gpio_dev_release()
--> gpio_free()
--> gpiod_free()
--> gpiod_free_commit()
--> gpiod_line_state_notify()
--> blocking_notifier_call_chain()
--> down_read(&nh->rwsem); <-- held rwsem
--> notifier_call_chain()
--> lineinfo_changed_notify()
--> test_bit(xxxx, cdev->watched_lines) <-- use after free
The side effect of the use-after-free issue is that a GPIO line event is
being generated for userspace where it shouldn't. However, since the chrdev
is being closed, userspace won't have the chance to read that event anyway.
To fix the issue, call the bitmap_free() function after the unregistration
of lineinfo_changed_nb notifier chain. |
| In the Linux kernel, the following vulnerability has been resolved:
fpga: bridge: add owner module and take its refcount
The current implementation of the fpga bridge assumes that the low-level
module registers a driver for the parent device and uses its owner pointer
to take the module's refcount. This approach is problematic since it can
lead to a null pointer dereference while attempting to get the bridge if
the parent device does not have a driver.
To address this problem, add a module owner pointer to the fpga_bridge
struct and use it to take the module's refcount. Modify the function for
registering a bridge to take an additional owner module parameter and
rename it to avoid conflicts. Use the old function name for a helper macro
that automatically sets the module that registers the bridge as the owner.
This ensures compatibility with existing low-level control modules and
reduces the chances of registering a bridge without setting the owner.
Also, update the documentation to keep it consistent with the new interface
for registering an fpga bridge.
Other changes: opportunistically move put_device() from __fpga_bridge_get()
to fpga_bridge_get() and of_fpga_bridge_get() to improve code clarity since
the bridge device is taken in these functions. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rtrs: Ensure 'ib_sge list' is accessible
Move the declaration of the 'ib_sge list' variable outside the
'always_invalidate' block to ensure it remains accessible for use
throughout the function.
Previously, 'ib_sge list' was declared within the 'always_invalidate'
block, limiting its accessibility, then caused a
'BUG: kernel NULL pointer dereference'[1].
? __die_body.cold+0x19/0x27
? page_fault_oops+0x15a/0x2d0
? search_module_extables+0x19/0x60
? search_bpf_extables+0x5f/0x80
? exc_page_fault+0x7e/0x180
? asm_exc_page_fault+0x26/0x30
? memcpy_orig+0xd5/0x140
rxe_mr_copy+0x1c3/0x200 [rdma_rxe]
? rxe_pool_get_index+0x4b/0x80 [rdma_rxe]
copy_data+0xa5/0x230 [rdma_rxe]
rxe_requester+0xd9b/0xf70 [rdma_rxe]
? finish_task_switch.isra.0+0x99/0x2e0
rxe_sender+0x13/0x40 [rdma_rxe]
do_task+0x68/0x1e0 [rdma_rxe]
process_one_work+0x177/0x330
worker_thread+0x252/0x390
? __pfx_worker_thread+0x10/0x10
This change ensures the variable is available for subsequent operations
that require it.
[1] https://lore.kernel.org/linux-rdma/6a1f3e8f-deb0-49f9-bc69-a9b03ecfcda7@fujitsu.com/ |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: Fix not validating setsockopt user input
Check user input length before copying data. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: qgroup: fix qgroup prealloc rsv leak in subvolume operations
Create subvolume, create snapshot and delete subvolume all use
btrfs_subvolume_reserve_metadata() to reserve metadata for the changes
done to the parent subvolume's fs tree, which cannot be mediated in the
normal way via start_transaction. When quota groups (squota or qgroups)
are enabled, this reserves qgroup metadata of type PREALLOC. Once the
operation is associated to a transaction, we convert PREALLOC to
PERTRANS, which gets cleared in bulk at the end of the transaction.
However, the error paths of these three operations were not implementing
this lifecycle correctly. They unconditionally converted the PREALLOC to
PERTRANS in a generic cleanup step regardless of errors or whether the
operation was fully associated to a transaction or not. This resulted in
error paths occasionally converting this rsv to PERTRANS without calling
record_root_in_trans successfully, which meant that unless that root got
recorded in the transaction by some other thread, the end of the
transaction would not free that root's PERTRANS, leaking it. Ultimately,
this resulted in hitting a WARN in CONFIG_BTRFS_DEBUG builds at unmount
for the leaked reservation.
The fix is to ensure that every qgroup PREALLOC reservation observes the
following properties:
1. any failure before record_root_in_trans is called successfully
results in freeing the PREALLOC reservation.
2. after record_root_in_trans, we convert to PERTRANS, and now the
transaction owns freeing the reservation.
This patch enforces those properties on the three operations. Without
it, generic/269 with squotas enabled at mkfs time would fail in ~5-10
runs on my system. With this patch, it ran successfully 1000 times in a
row. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: Fixed overflow check in mi_enum_attr() |
| In the Linux kernel, the following vulnerability has been resolved:
inet: inet_defrag: prevent sk release while still in use
ip_local_out() and other functions can pass skb->sk as function argument.
If the skb is a fragment and reassembly happens before such function call
returns, the sk must not be released.
This affects skb fragments reassembled via netfilter or similar
modules, e.g. openvswitch or ct_act.c, when run as part of tx pipeline.
Eric Dumazet made an initial analysis of this bug. Quoting Eric:
Calling ip_defrag() in output path is also implying skb_orphan(),
which is buggy because output path relies on sk not disappearing.
A relevant old patch about the issue was :
8282f27449bf ("inet: frag: Always orphan skbs inside ip_defrag()")
[..]
net/ipv4/ip_output.c depends on skb->sk being set, and probably to an
inet socket, not an arbitrary one.
If we orphan the packet in ipvlan, then downstream things like FQ
packet scheduler will not work properly.
We need to change ip_defrag() to only use skb_orphan() when really
needed, ie whenever frag_list is going to be used.
Eric suggested to stash sk in fragment queue and made an initial patch.
However there is a problem with this:
If skb is refragmented again right after, ip_do_fragment() will copy
head->sk to the new fragments, and sets up destructor to sock_wfree.
IOW, we have no choice but to fix up sk_wmem accouting to reflect the
fully reassembled skb, else wmem will underflow.
This change moves the orphan down into the core, to last possible moment.
As ip_defrag_offset is aliased with sk_buff->sk member, we must move the
offset into the FRAG_CB, else skb->sk gets clobbered.
This allows to delay the orphaning long enough to learn if the skb has
to be queued or if the skb is completing the reasm queue.
In the former case, things work as before, skb is orphaned. This is
safe because skb gets queued/stolen and won't continue past reasm engine.
In the latter case, we will steal the skb->sk reference, reattach it to
the head skb, and fix up wmem accouting when inet_frag inflates truesize. |
| In the Linux kernel, the following vulnerability has been resolved:
mlxsw: spectrum_acl_tcam: Fix NULL pointer dereference in error path
When calling mlxsw_sp_acl_tcam_region_destroy() from an error path after
failing to attach the region to an ACL group, we hit a NULL pointer
dereference upon 'region->group->tcam' [1].
Fix by retrieving the 'tcam' pointer using mlxsw_sp_acl_to_tcam().
[1]
BUG: kernel NULL pointer dereference, address: 0000000000000000
[...]
RIP: 0010:mlxsw_sp_acl_tcam_region_destroy+0xa0/0xd0
[...]
Call Trace:
mlxsw_sp_acl_tcam_vchunk_get+0x88b/0xa20
mlxsw_sp_acl_tcam_ventry_add+0x25/0xe0
mlxsw_sp_acl_rule_add+0x47/0x240
mlxsw_sp_flower_replace+0x1a9/0x1d0
tc_setup_cb_add+0xdc/0x1c0
fl_hw_replace_filter+0x146/0x1f0
fl_change+0xc17/0x1360
tc_new_tfilter+0x472/0xb90
rtnetlink_rcv_msg+0x313/0x3b0
netlink_rcv_skb+0x58/0x100
netlink_unicast+0x244/0x390
netlink_sendmsg+0x1e4/0x440
____sys_sendmsg+0x164/0x260
___sys_sendmsg+0x9a/0xe0
__sys_sendmsg+0x7a/0xc0
do_syscall_64+0x40/0xe0
entry_SYSCALL_64_after_hwframe+0x63/0x6b |
| In the Linux kernel, the following vulnerability has been resolved:
IORING_OP_READ did not correctly consume the provided buffer list when
read i/o returned < 0 (except for -EAGAIN and -EIOCBQUEUED return).
This can lead to a potential use-after-free when the completion via
io_rw_done runs at separate context. |
| In the Linux kernel, the following vulnerability has been resolved:
media: aspeed: Fix memory overwrite if timing is 1600x900
When capturing 1600x900, system could crash when system memory usage is
tight.
The way to reproduce this issue:
1. Use 1600x900 to display on host
2. Mount ISO through 'Virtual media' on OpenBMC's web
3. Run script as below on host to do sha continuously
#!/bin/bash
while [ [1] ];
do
find /media -type f -printf '"%h/%f"\n' | xargs sha256sum
done
4. Open KVM on OpenBMC's web
The size of macro block captured is 8x8. Therefore, we should make sure
the height of src-buf is 8 aligned to fix this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix potential key use-after-free
When ieee80211_key_link() is called by ieee80211_gtk_rekey_add()
but returns 0 due to KRACK protection (identical key reinstall),
ieee80211_gtk_rekey_add() will still return a pointer into the
key, in a potential use-after-free. This normally doesn't happen
since it's only called by iwlwifi in case of WoWLAN rekey offload
which has its own KRACK protection, but still better to fix, do
that by returning an error code and converting that to success on
the cfg80211 boundary only, leaving the error for bad callers of
ieee80211_gtk_rekey_add(). |
| In the Linux kernel, the following vulnerability has been resolved:
jfs: fix slab-out-of-bounds read in ea_get()
During the "size_check" label in ea_get(), the code checks if the extended
attribute list (xattr) size matches ea_size. If not, it logs
"ea_get: invalid extended attribute" and calls print_hex_dump().
Here, EALIST_SIZE(ea_buf->xattr) returns 4110417968, which exceeds
INT_MAX (2,147,483,647). Then ea_size is clamped:
int size = clamp_t(int, ea_size, 0, EALIST_SIZE(ea_buf->xattr));
Although clamp_t aims to bound ea_size between 0 and 4110417968, the upper
limit is treated as an int, causing an overflow above 2^31 - 1. This leads
"size" to wrap around and become negative (-184549328).
The "size" is then passed to print_hex_dump() (called "len" in
print_hex_dump()), it is passed as type size_t (an unsigned
type), this is then stored inside a variable called
"int remaining", which is then assigned to "int linelen" which
is then passed to hex_dump_to_buffer(). In print_hex_dump()
the for loop, iterates through 0 to len-1, where len is
18446744073525002176, calling hex_dump_to_buffer()
on each iteration:
for (i = 0; i < len; i += rowsize) {
linelen = min(remaining, rowsize);
remaining -= rowsize;
hex_dump_to_buffer(ptr + i, linelen, rowsize, groupsize,
linebuf, sizeof(linebuf), ascii);
...
}
The expected stopping condition (i < len) is effectively broken
since len is corrupted and very large. This eventually leads to
the "ptr+i" being passed to hex_dump_to_buffer() to get closer
to the end of the actual bounds of "ptr", eventually an out of
bounds access is done in hex_dump_to_buffer() in the following
for loop:
for (j = 0; j < len; j++) {
if (linebuflen < lx + 2)
goto overflow2;
ch = ptr[j];
...
}
To fix this we should validate "EALIST_SIZE(ea_buf->xattr)"
before it is utilised. |
| In the Linux kernel, the following vulnerability has been resolved:
clk: samsung: Fix UBSAN panic in samsung_clk_init()
With UBSAN_ARRAY_BOUNDS=y, I'm hitting the below panic due to
dereferencing `ctx->clk_data.hws` before setting
`ctx->clk_data.num = nr_clks`. Move that up to fix the crash.
UBSAN: array index out of bounds: 00000000f2005512 [#1] PREEMPT SMP
<snip>
Call trace:
samsung_clk_init+0x110/0x124 (P)
samsung_clk_init+0x48/0x124 (L)
samsung_cmu_register_one+0x3c/0xa0
exynos_arm64_register_cmu+0x54/0x64
__gs101_cmu_top_of_clk_init_declare+0x28/0x60
... |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: use aead_request_free to match aead_request_alloc
Use aead_request_free() instead of kfree() to properly free memory
allocated by aead_request_alloc(). This ensures sensitive crypto data
is zeroed before being freed. |
| In the Linux kernel, the following vulnerability has been resolved:
remoteproc: core: Clear table_sz when rproc_shutdown
There is case as below could trigger kernel dump:
Use U-Boot to start remote processor(rproc) with resource table
published to a fixed address by rproc. After Kernel boots up,
stop the rproc, load a new firmware which doesn't have resource table
,and start rproc.
When starting rproc with a firmware not have resource table,
`memcpy(loaded_table, rproc->cached_table, rproc->table_sz)` will
trigger dump, because rproc->cache_table is set to NULL during the last
stop operation, but rproc->table_sz is still valid.
This issue is found on i.MX8MP and i.MX9.
Dump as below:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Mem abort info:
ESR = 0x0000000096000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x04: level 0 translation fault
Data abort info:
ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000
CM = 0, WnR = 0, TnD = 0, TagAccess = 0
GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=000000010af63000
[0000000000000000] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
Modules linked in:
CPU: 2 UID: 0 PID: 1060 Comm: sh Not tainted 6.14.0-rc7-next-20250317-dirty #38
Hardware name: NXP i.MX8MPlus EVK board (DT)
pstate: a0000005 (NzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __pi_memcpy_generic+0x110/0x22c
lr : rproc_start+0x88/0x1e0
Call trace:
__pi_memcpy_generic+0x110/0x22c (P)
rproc_boot+0x198/0x57c
state_store+0x40/0x104
dev_attr_store+0x18/0x2c
sysfs_kf_write+0x7c/0x94
kernfs_fop_write_iter+0x120/0x1cc
vfs_write+0x240/0x378
ksys_write+0x70/0x108
__arm64_sys_write+0x1c/0x28
invoke_syscall+0x48/0x10c
el0_svc_common.constprop.0+0xc0/0xe0
do_el0_svc+0x1c/0x28
el0_svc+0x30/0xcc
el0t_64_sync_handler+0x10c/0x138
el0t_64_sync+0x198/0x19c
Clear rproc->table_sz to address the issue. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: prevent out-of-bounds stream writes by validating *pos
ksmbd_vfs_stream_write() did not validate whether the write offset
(*pos) was within the bounds of the existing stream data length (v_len).
If *pos was greater than or equal to v_len, this could lead to an
out-of-bounds memory write.
This patch adds a check to ensure *pos is less than v_len before
proceeding. If the condition fails, -EINVAL is returned. |
| In the Linux kernel, the following vulnerability has been resolved:
sound/virtio: Fix cancel_sync warnings on uninitialized work_structs
Betty reported hitting the following warning:
[ 8.709131][ T221] WARNING: CPU: 2 PID: 221 at kernel/workqueue.c:4182
...
[ 8.713282][ T221] Call trace:
[ 8.713365][ T221] __flush_work+0x8d0/0x914
[ 8.713468][ T221] __cancel_work_sync+0xac/0xfc
[ 8.713570][ T221] cancel_work_sync+0x24/0x34
[ 8.713667][ T221] virtsnd_remove+0xa8/0xf8 [virtio_snd ab15f34d0dd772f6d11327e08a81d46dc9c36276]
[ 8.713868][ T221] virtsnd_probe+0x48c/0x664 [virtio_snd ab15f34d0dd772f6d11327e08a81d46dc9c36276]
[ 8.714035][ T221] virtio_dev_probe+0x28c/0x390
[ 8.714139][ T221] really_probe+0x1bc/0x4c8
...
It seems we're hitting the error path in virtsnd_probe(), which
triggers a virtsnd_remove() which iterates over the substreams
calling cancel_work_sync() on the elapsed_period work_struct.
Looking at the code, from earlier in:
virtsnd_probe()->virtsnd_build_devs()->virtsnd_pcm_parse_cfg()
We set snd->nsubstreams, allocate the snd->substreams, and if
we then hit an error on the info allocation or something in
virtsnd_ctl_query_info() fails, we will exit without having
initialized the elapsed_period work_struct.
When that error path unwinds we then call virtsnd_remove()
which as long as the substreams array is allocated, will iterate
through calling cancel_work_sync() on the uninitialized work
struct hitting this warning.
Takashi Iwai suggested this fix, which initializes the substreams
structure right after allocation, so that if we hit the error
paths we avoid trying to cleanup uninitialized data.
Note: I have not yet managed to reproduce the issue myself, so
this patch has had limited testing.
Feedback or thoughts would be appreciated! |
| In the Linux kernel, the following vulnerability has been resolved:
udmabuf: fix a buf size overflow issue during udmabuf creation
by casting size_limit_mb to u64 when calculate pglimit. |
