| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: 8852a: rfk: fix div 0 exception
The DPK is a kind of RF calibration whose algorithm is to fine tune
parameters and calibrate, and check the result. If the result isn't good
enough, it could adjust parameters and try again.
This issue is to read and show the result, but it could be a negative
calibration result that causes divisor 0 and core dump. So, fix it by
phy_div() that does division only if divisor isn't zero; otherwise,
zero is adopted.
divide error: 0000 [#1] PREEMPT SMP NOPTI
CPU: 1 PID: 728 Comm: wpa_supplicant Not tainted 5.10.114-16019-g462a1661811a #1 <HASH:d024 28>
RIP: 0010:rtw8852a_dpk+0x14ae/0x288f [rtw89_core]
RSP: 0018:ffffa9bb412a7520 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 00000000000180fc RDI: ffffa141d01023c0
RBP: ffffa9bb412a76a0 R08: 0000000000001319 R09: 00000000ffffff92
R10: ffffffffc0292de3 R11: ffffffffc00d2f51 R12: 0000000000000000
R13: ffffa141d01023c0 R14: ffffffffc0290250 R15: ffffa141d0102638
FS: 00007fa99f5c2740(0000) GS:ffffa142e5e80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000013e8e010 CR3: 0000000110d2c000 CR4: 0000000000750ee0
PKRU: 55555554
Call Trace:
rtw89_core_sta_add+0x95/0x9c [rtw89_core <HASH:d239 29>]
rtw89_ops_sta_state+0x5d/0x108 [rtw89_core <HASH:d239 29>]
drv_sta_state+0x115/0x66f [mac80211 <HASH:81fe 30>]
sta_info_insert_rcu+0x45c/0x713 [mac80211 <HASH:81fe 30>]
sta_info_insert+0xf/0x1b [mac80211 <HASH:81fe 30>]
ieee80211_prep_connection+0x9d6/0xb0c [mac80211 <HASH:81fe 30>]
ieee80211_mgd_auth+0x2aa/0x352 [mac80211 <HASH:81fe 30>]
cfg80211_mlme_auth+0x160/0x1f6 [cfg80211 <HASH:00cd 31>]
nl80211_authenticate+0x2e5/0x306 [cfg80211 <HASH:00cd 31>]
genl_rcv_msg+0x371/0x3a1
? nl80211_stop_sched_scan+0xe5/0xe5 [cfg80211 <HASH:00cd 31>]
? genl_rcv+0x36/0x36
netlink_rcv_skb+0x8a/0xf9
genl_rcv+0x28/0x36
netlink_unicast+0x27b/0x3a0
netlink_sendmsg+0x2aa/0x469
sock_sendmsg_nosec+0x49/0x4d
____sys_sendmsg+0xe5/0x213
__sys_sendmsg+0xec/0x157
? syscall_enter_from_user_mode+0xd7/0x116
do_syscall_64+0x43/0x55
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fa99f6e689b |
| In the Linux kernel, the following vulnerability has been resolved:
PM: EM: Fix potential division-by-zero error in em_compute_costs()
When the device is of a non-CPU type, table[i].performance won't be
initialized in the previous em_init_performance(), resulting in division
by zero when calculating costs in em_compute_costs().
Since the 'cost' algorithm is only used for EAS energy efficiency
calculations and is currently not utilized by other device drivers, we
should add the _is_cpu_device(dev) check to prevent this division-by-zero
issue. |
| In the Linux kernel, the following vulnerability has been resolved:
video: fbdev: arkfb: Fix a divide-by-zero bug in ark_set_pixclock()
Since the user can control the arguments of the ioctl() from the user
space, under special arguments that may result in a divide-by-zero bug
in:
drivers/video/fbdev/arkfb.c:784: ark_set_pixclock(info, (hdiv * info->var.pixclock) / hmul);
with hdiv=1, pixclock=1 and hmul=2 you end up with (1*1)/2 = (int) 0.
and then in:
drivers/video/fbdev/arkfb.c:504: rv = dac_set_freq(par->dac, 0, 1000000000 / pixclock);
we'll get a division-by-zero.
The following log can reveal it:
divide error: 0000 [#1] PREEMPT SMP KASAN PTI
RIP: 0010:ark_set_pixclock drivers/video/fbdev/arkfb.c:504 [inline]
RIP: 0010:arkfb_set_par+0x10fc/0x24c0 drivers/video/fbdev/arkfb.c:784
Call Trace:
fb_set_var+0x604/0xeb0 drivers/video/fbdev/core/fbmem.c:1034
do_fb_ioctl+0x234/0x670 drivers/video/fbdev/core/fbmem.c:1110
fb_ioctl+0xdd/0x130 drivers/video/fbdev/core/fbmem.c:1189
Fix this by checking the argument of ark_set_pixclock() first. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon: fix divide by zero in damon_get_intervals_score()
The current implementation allows having zero size regions with no special
reasons, but damon_get_intervals_score() gets crashed by divide by zero
when the region size is zero.
[ 29.403950] Oops: divide error: 0000 [#1] SMP NOPTI
This patch fixes the bug, but does not disallow zero size regions to keep
the backward compatibility since disallowing zero size regions might be a
breaking change for some users.
In addition, the same crash can happen when intervals_goal.access_bp is
zero so this should be fixed in stable trees as well. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Avoid divide by zero by initializing dummy pitch to 1
[Why]
If the dummy values in `populate_dummy_dml_surface_cfg()` aren't updated
then they can lead to a divide by zero in downstream callers like
CalculateVMAndRowBytes()
[How]
Initialize dummy value to a value to avoid divide by zero. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: spi-mem: Add fix to avoid divide error
For some SPI flash memory operations, dummy bytes are not mandatory. For
example, in Winbond SPINAND flash memory devices, the `write_cache` and
`update_cache` operation variants have zero dummy bytes. Calculating the
duration for SPI memory operations with zero dummy bytes causes
a divide error when `ncycles` is calculated in the
spi_mem_calc_op_duration().
Add changes to skip the 'ncylcles' calculation for zero dummy bytes.
Following divide error is fixed by this change:
Oops: divide error: 0000 [#1] PREEMPT SMP NOPTI
...
? do_trap+0xdb/0x100
? do_error_trap+0x75/0xb0
? spi_mem_calc_op_duration+0x56/0xb0
? exc_divide_error+0x3b/0x70
? spi_mem_calc_op_duration+0x56/0xb0
? asm_exc_divide_error+0x1b/0x20
? spi_mem_calc_op_duration+0x56/0xb0
? spinand_select_op_variant+0xee/0x190 [spinand]
spinand_match_and_init+0x13e/0x1a0 [spinand]
spinand_manufacturer_match+0x6e/0xa0 [spinand]
spinand_probe+0x357/0x7f0 [spinand]
? kernfs_activate+0x87/0xd0
spi_mem_probe+0x7a/0xb0
spi_probe+0x7d/0x130 |
| In the Linux kernel, the following vulnerability has been resolved:
pwm: mediatek: Prevent divide-by-zero in pwm_mediatek_config()
With CONFIG_COMPILE_TEST && !CONFIG_HAVE_CLK, pwm_mediatek_config() has a
divide-by-zero in the following line:
do_div(resolution, clk_get_rate(pc->clk_pwms[pwm->hwpwm]));
due to the fact that the !CONFIG_HAVE_CLK version of clk_get_rate()
returns zero.
This is presumably just a theoretical problem: COMPILE_TEST overrides
the dependency on RALINK which would select COMMON_CLK. Regardless it's
a good idea to check for the error explicitly to avoid divide-by-zero.
Fixes the following warning:
drivers/pwm/pwm-mediatek.o: warning: objtool: .text: unexpected end of section
[ukleinek: s/CONFIG_CLK/CONFIG_HAVE_CLK/] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/pm: Prevent division by zero
The user can set any speed value.
If speed is greater than UINT_MAX/8, division by zero is possible.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/pm: Prevent division by zero
The user can set any speed value.
If speed is greater than UINT_MAX/8, division by zero is possible.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/pm: Prevent division by zero
The user can set any speed value.
If speed is greater than UINT_MAX/8, division by zero is possible.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/pm/smu11: Prevent division by zero
The user can set any speed value.
If speed is greater than UINT_MAX/8, division by zero is possible.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
(cherry picked from commit da7dc714a8f8e1c9fc33c57cd63583779a3bef71) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/pm: Prevent division by zero
The user can set any speed value.
If speed is greater than UINT_MAX/8, division by zero is possible.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/pm: Prevent division by zero
The user can set any speed value.
If speed is greater than UINT_MAX/8, division by zero is possible.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| An issue was discovered IW44EncodeCodec.cpp in djvulibre 3.5.28 in allows attackers to cause a denial of service via divide by zero. |
| An issue was discovered IW44Image.cpp in djvulibre 3.5.28 in allows attackers to cause a denial of service via divide by zero. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: cope racing subflow creation in mptcp_rcv_space_adjust
Additional active subflows - i.e. created by the in kernel path
manager - are included into the subflow list before starting the
3whs.
A racing recvmsg() spooling data received on an already established
subflow would unconditionally call tcp_cleanup_rbuf() on all the
current subflows, potentially hitting a divide by zero error on
the newly created ones.
Explicitly check that the subflow is in a suitable state before
invoking tcp_cleanup_rbuf(). |
| In the Linux kernel, the following vulnerability has been resolved:
media: v4l2-tpg: prevent the risk of a division by zero
As reported by Coverity, the logic at tpg_precalculate_line()
blindly rescales the buffer even when scaled_witdh is equal to
zero. If this ever happens, this will cause a division by zero.
Instead, add a WARN_ON_ONCE() to trigger such cases and return
without doing any precalculation. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: iio: frequency: ad9832: fix division by zero in ad9832_calc_freqreg()
In the ad9832_write_frequency() function, clk_get_rate() might return 0.
This can lead to a division by zero when calling ad9832_calc_freqreg().
The check if (fout > (clk_get_rate(st->mclk) / 2)) does not protect
against the case when fout is 0. The ad9832_write_frequency() function
is called from ad9832_write(), and fout is derived from a text buffer,
which can contain any value. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ad7124: fix division by zero in ad7124_set_channel_odr()
In the ad7124_write_raw() function, parameter val can potentially
be zero. This may lead to a division by zero when DIV_ROUND_CLOSEST()
is called within ad7124_set_channel_odr(). The ad7124_write_raw()
function is invoked through the sequence: iio_write_channel_raw() ->
iio_write_channel_attribute() -> iio_channel_write(), with no checks
in place to ensure val is non-zero. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: firewire-lib: Avoid division by zero in apply_constraint_to_size()
The step variable is initialized to zero. It is changed in the loop,
but if it's not changed it will remain zero. Add a variable check
before the division.
The observed behavior was introduced by commit 826b5de90c0b
("ALSA: firewire-lib: fix insufficient PCM rule for period/buffer size"),
and it is difficult to show that any of the interval parameters will
satisfy the snd_interval_test() condition with data from the
amdtp_rate_table[] table.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
