| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: fix ipv4 null-ptr-deref in route error path
The IPv4 code path in __ip_vs_get_out_rt() calls dst_link_failure()
without ensuring skb->dev is set, leading to a NULL pointer dereference
in fib_compute_spec_dst() when ipv4_link_failure() attempts to send
ICMP destination unreachable messages.
The issue emerged after commit ed0de45a1008 ("ipv4: recompile ip options
in ipv4_link_failure") started calling __ip_options_compile() from
ipv4_link_failure(). This code path eventually calls fib_compute_spec_dst()
which dereferences skb->dev. An attempt was made to fix the NULL skb->dev
dereference in commit 0113d9c9d1cc ("ipv4: fix null-deref in
ipv4_link_failure"), but it only addressed the immediate dev_net(skb->dev)
dereference by using a fallback device. The fix was incomplete because
fib_compute_spec_dst() later in the call chain still accesses skb->dev
directly, which remains NULL when IPVS calls dst_link_failure().
The crash occurs when:
1. IPVS processes a packet in NAT mode with a misconfigured destination
2. Route lookup fails in __ip_vs_get_out_rt() before establishing a route
3. The error path calls dst_link_failure(skb) with skb->dev == NULL
4. ipv4_link_failure() → ipv4_send_dest_unreach() →
__ip_options_compile() → fib_compute_spec_dst()
5. fib_compute_spec_dst() dereferences NULL skb->dev
Apply the same fix used for IPv6 in commit 326bf17ea5d4 ("ipvs: fix
ipv6 route unreach panic"): set skb->dev from skb_dst(skb)->dev before
calling dst_link_failure().
KASAN: null-ptr-deref in range [0x0000000000000328-0x000000000000032f]
CPU: 1 PID: 12732 Comm: syz.1.3469 Not tainted 6.6.114 #2
RIP: 0010:__in_dev_get_rcu include/linux/inetdevice.h:233
RIP: 0010:fib_compute_spec_dst+0x17a/0x9f0 net/ipv4/fib_frontend.c:285
Call Trace:
<TASK>
spec_dst_fill net/ipv4/ip_options.c:232
spec_dst_fill net/ipv4/ip_options.c:229
__ip_options_compile+0x13a1/0x17d0 net/ipv4/ip_options.c:330
ipv4_send_dest_unreach net/ipv4/route.c:1252
ipv4_link_failure+0x702/0xb80 net/ipv4/route.c:1265
dst_link_failure include/net/dst.h:437
__ip_vs_get_out_rt+0x15fd/0x19e0 net/netfilter/ipvs/ip_vs_xmit.c:412
ip_vs_nat_xmit+0x1d8/0xc80 net/netfilter/ipvs/ip_vs_xmit.c:764 |
| In the Linux kernel, the following vulnerability has been resolved:
media: iris: Add sanity check for stop streaming
Add sanity check in iris_vb2_stop_streaming. If inst->state is
already IRIS_INST_ERROR, we should skip the stream_off operation
because it would still send packets to the firmware.
In iris_kill_session, inst->state is set to IRIS_INST_ERROR and
session_close is executed, which will kfree(inst_hfi_gen2->packet).
If stop_streaming is called afterward, it will cause a crash.
[bod: remove qcom from patch title] |
| In the Linux kernel, the following vulnerability has been resolved:
svcrdma: use rc_pageoff for memcpy byte offset
svc_rdma_copy_inline_range added rc_curpage (page index) to the page
base instead of the byte offset rc_pageoff. Use rc_pageoff so copies
land within the current page.
Found by ZeroPath (https://zeropath.com) |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: Disallow toggling KVM_MEM_GUEST_MEMFD on an existing memslot
Reject attempts to disable KVM_MEM_GUEST_MEMFD on a memslot that was
initially created with a guest_memfd binding, as KVM doesn't support
toggling KVM_MEM_GUEST_MEMFD on existing memslots. KVM prevents enabling
KVM_MEM_GUEST_MEMFD, but doesn't prevent clearing the flag.
Failure to reject the new memslot results in a use-after-free due to KVM
not unbinding from the guest_memfd instance. Unbinding on a FLAGS_ONLY
change is easy enough, and can/will be done as a hardening measure (in
anticipation of KVM supporting dirty logging on guest_memfd at some point),
but fixing the use-after-free would only address the immediate symptom.
==================================================================
BUG: KASAN: slab-use-after-free in kvm_gmem_release+0x362/0x400 [kvm]
Write of size 8 at addr ffff8881111ae908 by task repro/745
CPU: 7 UID: 1000 PID: 745 Comm: repro Not tainted 6.18.0-rc6-115d5de2eef3-next-kasan #3 NONE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
Call Trace:
<TASK>
dump_stack_lvl+0x51/0x60
print_report+0xcb/0x5c0
kasan_report+0xb4/0xe0
kvm_gmem_release+0x362/0x400 [kvm]
__fput+0x2fa/0x9d0
task_work_run+0x12c/0x200
do_exit+0x6ae/0x2100
do_group_exit+0xa8/0x230
__x64_sys_exit_group+0x3a/0x50
x64_sys_call+0x737/0x740
do_syscall_64+0x5b/0x900
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x7f581f2eac31
</TASK>
Allocated by task 745 on cpu 6 at 9.746971s:
kasan_save_stack+0x20/0x40
kasan_save_track+0x13/0x50
__kasan_kmalloc+0x77/0x90
kvm_set_memory_region.part.0+0x652/0x1110 [kvm]
kvm_vm_ioctl+0x14b0/0x3290 [kvm]
__x64_sys_ioctl+0x129/0x1a0
do_syscall_64+0x5b/0x900
entry_SYSCALL_64_after_hwframe+0x4b/0x53
Freed by task 745 on cpu 6 at 9.747467s:
kasan_save_stack+0x20/0x40
kasan_save_track+0x13/0x50
__kasan_save_free_info+0x37/0x50
__kasan_slab_free+0x3b/0x60
kfree+0xf5/0x440
kvm_set_memslot+0x3c2/0x1160 [kvm]
kvm_set_memory_region.part.0+0x86a/0x1110 [kvm]
kvm_vm_ioctl+0x14b0/0x3290 [kvm]
__x64_sys_ioctl+0x129/0x1a0
do_syscall_64+0x5b/0x900
entry_SYSCALL_64_after_hwframe+0x4b/0x53 |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: vfs: fix race on m_flags in vfs_cache
ksmbd maintains delete-on-close and pending-delete state in
ksmbd_inode->m_flags. In vfs_cache.c this field is accessed under
inconsistent locking: some paths read and modify m_flags under
ci->m_lock while others do so without taking the lock at all.
Examples:
- ksmbd_query_inode_status() and __ksmbd_inode_close() use
ci->m_lock when checking or updating m_flags.
- ksmbd_inode_pending_delete(), ksmbd_set_inode_pending_delete(),
ksmbd_clear_inode_pending_delete() and ksmbd_fd_set_delete_on_close()
used to read and modify m_flags without ci->m_lock.
This creates a potential data race on m_flags when multiple threads
open, close and delete the same file concurrently. In the worst case
delete-on-close and pending-delete bits can be lost or observed in an
inconsistent state, leading to confusing delete semantics (files that
stay on disk after delete-on-close, or files that disappear while still
in use).
Fix it by:
- Making ksmbd_query_inode_status() look at m_flags under ci->m_lock
after dropping inode_hash_lock.
- Adding ci->m_lock protection to all helpers that read or modify
m_flags (ksmbd_inode_pending_delete(), ksmbd_set_inode_pending_delete(),
ksmbd_clear_inode_pending_delete(), ksmbd_fd_set_delete_on_close()).
- Keeping the existing ci->m_lock protection in __ksmbd_inode_close(),
and moving the actual unlink/xattr removal outside the lock.
This unifies the locking around m_flags and removes the data race while
preserving the existing delete-on-close behaviour. |
| In the Linux kernel, the following vulnerability has been resolved:
media: vidtv: initialize local pointers upon transfer of memory ownership
vidtv_channel_si_init() creates a temporary list (program, service, event)
and ownership of the memory itself is transferred to the PAT/SDT/EIT
tables through vidtv_psi_pat_program_assign(),
vidtv_psi_sdt_service_assign(), vidtv_psi_eit_event_assign().
The problem here is that the local pointer where the memory ownership
transfer was completed is not initialized to NULL. This causes the
vidtv_psi_pmt_create_sec_for_each_pat_entry() function to fail, and
in the flow that jumps to free_eit, the memory that was freed by
vidtv_psi_*_table_destroy() can be accessed again by
vidtv_psi_*_event_destroy() due to the uninitialized local pointer, so it
is freed once again.
Therefore, to prevent use-after-free and double-free vulnerability,
local pointers must be initialized to NULL when transferring memory
ownership. |
| In the Linux kernel, the following vulnerability has been resolved:
block: fix race between wbt_enable_default and IO submission
When wbt_enable_default() is moved out of queue freezing in elevator_change(),
it can cause the wbt inflight counter to become negative (-1), leading to hung
tasks in the writeback path. Tasks get stuck in wbt_wait() because the counter
is in an inconsistent state.
The issue occurs because wbt_enable_default() could race with IO submission,
allowing the counter to be decremented before proper initialization. This manifests
as:
rq_wait[0]:
inflight: -1
has_waiters: True
rwb_enabled() checks the state, which can be updated exactly between wbt_wait()
(rq_qos_throttle()) and wbt_track()(rq_qos_track()), then the inflight counter
will become negative.
And results in hung task warnings like:
task:kworker/u24:39 state:D stack:0 pid:14767
Call Trace:
rq_qos_wait+0xb4/0x150
wbt_wait+0xa9/0x100
__rq_qos_throttle+0x24/0x40
blk_mq_submit_bio+0x672/0x7b0
...
Fix this by:
1. Splitting wbt_enable_default() into:
- __wbt_enable_default(): Returns true if wbt_init() should be called
- wbt_enable_default(): Wrapper for existing callers (no init)
- wbt_init_enable_default(): New function that checks and inits WBT
2. Using wbt_init_enable_default() in blk_register_queue() to ensure
proper initialization during queue registration
3. Move wbt_init() out of wbt_enable_default() which is only for enabling
disabled wbt from bfq and iocost, and wbt_init() isn't needed. Then the
original lock warning can be avoided.
4. Removing the ELEVATOR_FLAG_ENABLE_WBT_ON_EXIT flag and its handling
code since it's no longer needed
This ensures WBT is properly initialized before any IO can be submitted,
preventing the counter from going negative. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix buffer validation by including null terminator size in EA length
The smb2_set_ea function, which handles Extended Attributes (EA),
was performing buffer validation checks that incorrectly omitted the size
of the null terminating character (+1 byte) for EA Name.
This patch fixes the issue by explicitly adding '+ 1' to EaNameLength where
the null terminator is expected to be present in the buffer, ensuring
the validation accurately reflects the total required buffer size. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse: fix io-uring list corruption for terminated non-committed requests
When a request is terminated before it has been committed, the request
is not removed from the queue's list. This leaves a dangling list entry
that leads to list corruption and use-after-free issues.
Remove the request from the queue's list for terminated non-committed
requests. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/chrome: cros_ec_ishtp: Fix UAF after unbinding driver
After unbinding the driver, another kthread `cros_ec_console_log_work`
is still accessing the device, resulting an UAF and crash.
The driver doesn't unregister the EC device in .remove() which should
shutdown sub-devices synchronously. Fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: NFSv4 file creation neglects setting ACL
An NFSv4 client that sets an ACL with a named principal during file
creation retrieves the ACL afterwards, and finds that it is only a
default ACL (based on the mode bits) and not the ACL that was
requested during file creation. This violates RFC 8881 section
6.4.1.3: "the ACL attribute is set as given".
The issue occurs in nfsd_create_setattr(), which calls
nfsd_attrs_valid() to determine whether to call nfsd_setattr().
However, nfsd_attrs_valid() checks only for iattr changes and
security labels, but not POSIX ACLs. When only an ACL is present,
the function returns false, nfsd_setattr() is skipped, and the
POSIX ACL is never applied to the inode.
Subsequently, when the client retrieves the ACL, the server finds
no POSIX ACL on the inode and returns one generated from the file's
mode bits rather than returning the originally-specified ACL. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe: Limit num_syncs to prevent oversized allocations
The exec and vm_bind ioctl allow userspace to specify an arbitrary
num_syncs value. Without bounds checking, a very large num_syncs
can force an excessively large allocation, leading to kernel warnings
from the page allocator as below.
Introduce DRM_XE_MAX_SYNCS (set to 1024) and reject any request
exceeding this limit.
"
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1217 at mm/page_alloc.c:5124 __alloc_frozen_pages_noprof+0x2f8/0x2180 mm/page_alloc.c:5124
...
Call Trace:
<TASK>
alloc_pages_mpol+0xe4/0x330 mm/mempolicy.c:2416
___kmalloc_large_node+0xd8/0x110 mm/slub.c:4317
__kmalloc_large_node_noprof+0x18/0xe0 mm/slub.c:4348
__do_kmalloc_node mm/slub.c:4364 [inline]
__kmalloc_noprof+0x3d4/0x4b0 mm/slub.c:4388
kmalloc_noprof include/linux/slab.h:909 [inline]
kmalloc_array_noprof include/linux/slab.h:948 [inline]
xe_exec_ioctl+0xa47/0x1e70 drivers/gpu/drm/xe/xe_exec.c:158
drm_ioctl_kernel+0x1f1/0x3e0 drivers/gpu/drm/drm_ioctl.c:797
drm_ioctl+0x5e7/0xc50 drivers/gpu/drm/drm_ioctl.c:894
xe_drm_ioctl+0x10b/0x170 drivers/gpu/drm/xe/xe_device.c:224
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:598 [inline]
__se_sys_ioctl fs/ioctl.c:584 [inline]
__x64_sys_ioctl+0x18b/0x210 fs/ioctl.c:584
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xbb/0x380 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
...
"
v2: Add "Reported-by" and Cc stable kernels.
v3: Change XE_MAX_SYNCS from 64 to 1024. (Matt & Ashutosh)
v4: s/XE_MAX_SYNCS/DRM_XE_MAX_SYNCS/ (Matt)
v5: Do the check at the top of the exec func. (Matt)
(cherry picked from commit b07bac9bd708ec468cd1b8a5fe70ae2ac9b0a11c) |
| In the Linux kernel, the following vulnerability has been resolved:
mlxsw: spectrum_router: Fix neighbour use-after-free
We sometimes observe use-after-free when dereferencing a neighbour [1].
The problem seems to be that the driver stores a pointer to the
neighbour, but without holding a reference on it. A reference is only
taken when the neighbour is used by a nexthop.
Fix by simplifying the reference counting scheme. Always take a
reference when storing a neighbour pointer in a neighbour entry. Avoid
taking a referencing when the neighbour is used by a nexthop as the
neighbour entry associated with the nexthop already holds a reference.
Tested by running the test that uncovered the problem over 300 times.
Without this patch the problem was reproduced after a handful of
iterations.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_neigh_entry_update+0x2d4/0x310
Read of size 8 at addr ffff88817f8e3420 by task ip/3929
CPU: 3 UID: 0 PID: 3929 Comm: ip Not tainted 6.18.0-rc4-virtme-g36b21a067510 #3 PREEMPT(full)
Hardware name: Nvidia SN5600/VMOD0013, BIOS 5.13 05/31/2023
Call Trace:
<TASK>
dump_stack_lvl+0x6f/0xa0
print_address_description.constprop.0+0x6e/0x300
print_report+0xfc/0x1fb
kasan_report+0xe4/0x110
mlxsw_sp_neigh_entry_update+0x2d4/0x310
mlxsw_sp_router_rif_gone_sync+0x35f/0x510
mlxsw_sp_rif_destroy+0x1ea/0x730
mlxsw_sp_inetaddr_port_vlan_event+0xa1/0x1b0
__mlxsw_sp_inetaddr_lag_event+0xcc/0x130
__mlxsw_sp_inetaddr_event+0xf5/0x3c0
mlxsw_sp_router_netdevice_event+0x1015/0x1580
notifier_call_chain+0xcc/0x150
call_netdevice_notifiers_info+0x7e/0x100
__netdev_upper_dev_unlink+0x10b/0x210
netdev_upper_dev_unlink+0x79/0xa0
vrf_del_slave+0x18/0x50
do_set_master+0x146/0x7d0
do_setlink.isra.0+0x9a0/0x2880
rtnl_newlink+0x637/0xb20
rtnetlink_rcv_msg+0x6fe/0xb90
netlink_rcv_skb+0x123/0x380
netlink_unicast+0x4a3/0x770
netlink_sendmsg+0x75b/0xc90
__sock_sendmsg+0xbe/0x160
____sys_sendmsg+0x5b2/0x7d0
___sys_sendmsg+0xfd/0x180
__sys_sendmsg+0x124/0x1c0
do_syscall_64+0xbb/0xfd0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
[...]
Allocated by task 109:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x7b/0x90
__kmalloc_noprof+0x2c1/0x790
neigh_alloc+0x6af/0x8f0
___neigh_create+0x63/0xe90
mlxsw_sp_nexthop_neigh_init+0x430/0x7e0
mlxsw_sp_nexthop_type_init+0x212/0x960
mlxsw_sp_nexthop6_group_info_init.constprop.0+0x81f/0x1280
mlxsw_sp_nexthop6_group_get+0x392/0x6a0
mlxsw_sp_fib6_entry_create+0x46a/0xfd0
mlxsw_sp_router_fib6_replace+0x1ed/0x5f0
mlxsw_sp_router_fib6_event_work+0x10a/0x2a0
process_one_work+0xd57/0x1390
worker_thread+0x4d6/0xd40
kthread+0x355/0x5b0
ret_from_fork+0x1d4/0x270
ret_from_fork_asm+0x11/0x20
Freed by task 154:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_save_free_info+0x3b/0x60
__kasan_slab_free+0x43/0x70
kmem_cache_free_bulk.part.0+0x1eb/0x5e0
kvfree_rcu_bulk+0x1f2/0x260
kfree_rcu_work+0x130/0x1b0
process_one_work+0xd57/0x1390
worker_thread+0x4d6/0xd40
kthread+0x355/0x5b0
ret_from_fork+0x1d4/0x270
ret_from_fork_asm+0x11/0x20
Last potentially related work creation:
kasan_save_stack+0x30/0x50
kasan_record_aux_stack+0x8c/0xa0
kvfree_call_rcu+0x93/0x5b0
mlxsw_sp_router_neigh_event_work+0x67d/0x860
process_one_work+0xd57/0x1390
worker_thread+0x4d6/0xd40
kthread+0x355/0x5b0
ret_from_fork+0x1d4/0x270
ret_from_fork_asm+0x11/0x20 |
| In the Linux kernel, the following vulnerability has been resolved:
mlxsw: spectrum_mr: Fix use-after-free when updating multicast route stats
Cited commit added a dedicated mutex (instead of RTNL) to protect the
multicast route list, so that it will not change while the driver
periodically traverses it in order to update the kernel about multicast
route stats that were queried from the device.
One instance of list entry deletion (during route replace) was missed
and it can result in a use-after-free [1].
Fix by acquiring the mutex before deleting the entry from the list and
releasing it afterwards.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_mr_stats_update+0x4a5/0x540 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:1006 [mlxsw_spectrum]
Read of size 8 at addr ffff8881523c2fa8 by task kworker/2:5/22043
CPU: 2 UID: 0 PID: 22043 Comm: kworker/2:5 Not tainted 6.18.0-rc1-custom-g1a3d6d7cd014 #1 PREEMPT(full)
Hardware name: Mellanox Technologies Ltd. MSN2010/SA002610, BIOS 5.6.5 08/24/2017
Workqueue: mlxsw_core mlxsw_sp_mr_stats_update [mlxsw_spectrum]
Call Trace:
<TASK>
dump_stack_lvl+0xba/0x110
print_report+0x174/0x4f5
kasan_report+0xdf/0x110
mlxsw_sp_mr_stats_update+0x4a5/0x540 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:1006 [mlxsw_spectrum]
process_one_work+0x9cc/0x18e0
worker_thread+0x5df/0xe40
kthread+0x3b8/0x730
ret_from_fork+0x3e9/0x560
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 29933:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x8f/0xa0
mlxsw_sp_mr_route_add+0xd8/0x4770 [mlxsw_spectrum]
mlxsw_sp_router_fibmr_event_work+0x371/0xad0 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:7965 [mlxsw_spectrum]
process_one_work+0x9cc/0x18e0
worker_thread+0x5df/0xe40
kthread+0x3b8/0x730
ret_from_fork+0x3e9/0x560
ret_from_fork_asm+0x1a/0x30
Freed by task 29933:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_save_free_info+0x3b/0x70
__kasan_slab_free+0x43/0x70
kfree+0x14e/0x700
mlxsw_sp_mr_route_add+0x2dea/0x4770 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:444 [mlxsw_spectrum]
mlxsw_sp_router_fibmr_event_work+0x371/0xad0 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:7965 [mlxsw_spectrum]
process_one_work+0x9cc/0x18e0
worker_thread+0x5df/0xe40
kthread+0x3b8/0x730
ret_from_fork+0x3e9/0x560
ret_from_fork_asm+0x1a/0x30 |
| In the Linux kernel, the following vulnerability has been resolved:
caif: fix integer underflow in cffrml_receive()
The cffrml_receive() function extracts a length field from the packet
header and, when FCS is disabled, subtracts 2 from this length without
validating that len >= 2.
If an attacker sends a malicious packet with a length field of 0 or 1
to an interface with FCS disabled, the subtraction causes an integer
underflow.
This can lead to memory exhaustion and kernel instability, potential
information disclosure if padding contains uninitialized kernel memory.
Fix this by validating that len >= 2 before performing the subtraction. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/amd: Check event before enable to avoid GPF
On AMD machines cpuc->events[idx] can become NULL in a subtle race
condition with NMI->throttle->x86_pmu_stop().
Check event for NULL in amd_pmu_enable_all() before enable to avoid a GPF.
This appears to be an AMD only issue.
Syzkaller reported a GPF in amd_pmu_enable_all.
INFO: NMI handler (perf_event_nmi_handler) took too long to run: 13.143
msecs
Oops: general protection fault, probably for non-canonical address
0xdffffc0000000034: 0000 PREEMPT SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x00000000000001a0-0x00000000000001a7]
CPU: 0 UID: 0 PID: 328415 Comm: repro_36674776 Not tainted 6.12.0-rc1-syzk
RIP: 0010:x86_pmu_enable_event (arch/x86/events/perf_event.h:1195
arch/x86/events/core.c:1430)
RSP: 0018:ffff888118009d60 EFLAGS: 00010012
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000034 RSI: 0000000000000000 RDI: 00000000000001a0
RBP: 0000000000000001 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000002
R13: ffff88811802a440 R14: ffff88811802a240 R15: ffff8881132d8601
FS: 00007f097dfaa700(0000) GS:ffff888118000000(0000) GS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000200001c0 CR3: 0000000103d56000 CR4: 00000000000006f0
Call Trace:
<IRQ>
amd_pmu_enable_all (arch/x86/events/amd/core.c:760 (discriminator 2))
x86_pmu_enable (arch/x86/events/core.c:1360)
event_sched_out (kernel/events/core.c:1191 kernel/events/core.c:1186
kernel/events/core.c:2346)
__perf_remove_from_context (kernel/events/core.c:2435)
event_function (kernel/events/core.c:259)
remote_function (kernel/events/core.c:92 (discriminator 1)
kernel/events/core.c:72 (discriminator 1))
__flush_smp_call_function_queue (./arch/x86/include/asm/jump_label.h:27
./include/linux/jump_label.h:207 ./include/trace/events/csd.h:64
kernel/smp.c:135 kernel/smp.c:540)
__sysvec_call_function_single (./arch/x86/include/asm/jump_label.h:27
./include/linux/jump_label.h:207
./arch/x86/include/asm/trace/irq_vectors.h:99 arch/x86/kernel/smp.c:272)
sysvec_call_function_single (arch/x86/kernel/smp.c:266 (discriminator 47)
arch/x86/kernel/smp.c:266 (discriminator 47))
</IRQ> |
| In the Linux kernel, the following vulnerability has been resolved:
char: applicom: fix NULL pointer dereference in ac_ioctl
Discovered by Atuin - Automated Vulnerability Discovery Engine.
In ac_ioctl, the validation of IndexCard and the check for a valid
RamIO pointer are skipped when cmd is 6. However, the function
unconditionally executes readb(apbs[IndexCard].RamIO + VERS) at the
end.
If cmd is 6, IndexCard may reference a board that does not exist
(where RamIO is NULL), leading to a NULL pointer dereference.
Fix this by skipping the readb access when cmd is 6, as this
command is a global information query and does not target a specific
board context. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to avoid updating zero-sized extent in extent cache
As syzbot reported:
F2FS-fs (loop0): __update_extent_tree_range: extent len is zero, type: 0, extent [0, 0, 0], age [0, 0]
------------[ cut here ]------------
kernel BUG at fs/f2fs/extent_cache.c:678!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 0 UID: 0 PID: 5336 Comm: syz.0.0 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
RIP: 0010:__update_extent_tree_range+0x13bc/0x1500 fs/f2fs/extent_cache.c:678
Call Trace:
<TASK>
f2fs_update_read_extent_cache_range+0x192/0x3e0 fs/f2fs/extent_cache.c:1085
f2fs_do_zero_range fs/f2fs/file.c:1657 [inline]
f2fs_zero_range+0x10c1/0x1580 fs/f2fs/file.c:1737
f2fs_fallocate+0x583/0x990 fs/f2fs/file.c:2030
vfs_fallocate+0x669/0x7e0 fs/open.c:342
ioctl_preallocate fs/ioctl.c:289 [inline]
file_ioctl+0x611/0x780 fs/ioctl.c:-1
do_vfs_ioctl+0xb33/0x1430 fs/ioctl.c:576
__do_sys_ioctl fs/ioctl.c:595 [inline]
__se_sys_ioctl+0x82/0x170 fs/ioctl.c:583
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f07bc58eec9
In error path of f2fs_zero_range(), it may add a zero-sized extent
into extent cache, it should be avoided. |
| In the Linux kernel, the following vulnerability has been resolved:
ethtool: Avoid overflowing userspace buffer on stats query
The ethtool -S command operates across three ioctl calls:
ETHTOOL_GSSET_INFO for the size, ETHTOOL_GSTRINGS for the names, and
ETHTOOL_GSTATS for the values.
If the number of stats changes between these calls (e.g., due to device
reconfiguration), userspace's buffer allocation will be incorrect,
potentially leading to buffer overflow.
Drivers are generally expected to maintain stable stat counts, but some
drivers (e.g., mlx5, bnx2x, bna, ksz884x) use dynamic counters, making
this scenario possible.
Some drivers try to handle this internally:
- bnad_get_ethtool_stats() returns early in case stats.n_stats is not
equal to the driver's stats count.
- micrel/ksz884x also makes sure not to write anything beyond
stats.n_stats and overflow the buffer.
However, both use stats.n_stats which is already assigned with the value
returned from get_sset_count(), hence won't solve the issue described
here.
Change ethtool_get_strings(), ethtool_get_stats(),
ethtool_get_phy_stats() to not return anything in case of a mismatch
between userspace's size and get_sset_size(), to prevent buffer
overflow.
The returned n_stats value will be equal to zero, to reflect that
nothing has been returned.
This could result in one of two cases when using upstream ethtool,
depending on when the size change is detected:
1. When detected in ethtool_get_strings():
# ethtool -S eth2
no stats available
2. When detected in get stats, all stats will be reported as zero.
Both cases are presumably transient, and a subsequent ethtool call
should succeed.
Other than the overflow avoidance, these two cases are very evident (no
output/cleared stats), which is arguably better than presenting
incorrect/shifted stats.
I also considered returning an error instead of a "silent" response, but
that seems more destructive towards userspace apps.
Notes:
- This patch does not claim to fix the inherent race, it only makes sure
that we do not overflow the userspace buffer, and makes for a more
predictable behavior.
- RTNL lock is held during each ioctl, the race window exists between
the separate ioctl calls when the lock is released.
- Userspace ethtool always fills stats.n_stats, but it is likely that
these stats ioctls are implemented in other userspace applications
which might not fill it. The added code checks that it's not zero,
to prevent any regressions. |
| In the Linux kernel, the following vulnerability has been resolved:
iomap: adjust read range correctly for non-block-aligned positions
iomap_adjust_read_range() assumes that the position and length passed in
are block-aligned. This is not always the case however, as shown in the
syzbot generated case for erofs. This causes too many bytes to be
skipped for uptodate blocks, which results in returning the incorrect
position and length to read in. If all the blocks are uptodate, this
underflows length and returns a position beyond the folio.
Fix the calculation to also take into account the block offset when
calculating how many bytes can be skipped for uptodate blocks. |
